Usi Electric Micn109 Replacement

Usi Electric Micn109 Replacement Rating: 7,1/10 4617 votes

MODEL MICN102, MICN102LIONIZATION SMOKE ALARM,CARBON MONOXIDE ALARM ANDNATURAL GAS ALARMWITH BATTERY BACKUPAND SILENCE FEATUREMODEL MICN109, MICN109LIONIZATION SMOKE ALARM,CARBON MONOXIDE ALARM ANDNATURAL GAS ALARMWITH BATTERY BACKUPAND SILENCE FEATUREPLEASE READ AND SAVE!THANK YOU for purchasing this combination alarm. It is designed to detect smoke, carbon monoxide and natural gas (methane) which reaches the sensor. It is not designed to detect fire, heat, flames or any other gas.

  1. Usi Electric Smoke And Carbon Monoxide Detector Manual

This manual includes important information regarding where to install the alarm, how to operate, maintenance, testing and product features. It also includes tips and information which could help protect you and your family.Table of Contents:Page #What You Should Know About CO.2What You Should Know About Natural Gas.2Basic Safety Information.3Recommended Location of Alarms.4Avoid These Locations.4How to Install.5Operation & Alarm Characteristics.6What To Do If The Alarm Sounds.7Silence Feature.7Testing & Maintenance.8Battery Replacement.8CO & Natural Gas Alarm Limitations.9Operational Summary.11Warranty.Back Cover. ALARM LIMITATIONS AND FUNCTIONS This Combination Ionization Smoke/Carbon Monoxide (CO)/Natural Gas alarm requires constant 120 VAC power to operate properly. There are three basic smoke alarm types: IoPhic, Ionization and Photoelectric.IoPhic is an ionization alarm containing a patent-pendingUniversal Smoke Sensing Technology. IoPhic alarms are very effective at detecting fast flaming fires and also respond very quickly to slow smoldering fires - up to 87% faster than the maximum allowable alarm limit (UL217 Smoldering Smoke Test on 5/26/2010, Underwriters Laboratories Project #09CA38078).Ionization smoke alarms are typically more effective at detecting fast flaming fires - fires which consume combustible materials rapidly and spread quickly. Sources of these fires may include paper burning in a wastebasket, or kitchen grease fires.Photoelectric smoke alarms, on the other hand, are typically more effective at detecting slow smoldering fires - fires which burn for hours before bursting into flame. Sources of these fires may include cigarettes burning in couches or bedding.Installing IoPhic smoke alarms ensures maximum detection of both types of fires from a single alarm, while eliminating the need for a combination of ionization and photoelectric smoke alarms.The enclosed alarm is a Smoke, CO and Natural Gas alarm. SMOKE ALARMS WILL NOT WORK DURING A LOSS OF POWER.

  1. How do I stop my USI Electric Smoke Alarms that are hard-wired from chirping? The started by just beeping every couple of minutes. Then, one will beep 3 times, and the rest will each beep 3 time in 'response'. When I say beep, I mean like sirens are going off. Then they move on to chirping during which you wish you didn't have ear drums.
  2. USI Electric MICN109 Description. The Combination Smoke Alarm features four LED indicators for power, smoke, carbon monoxide and natural gas indication. The fire detector emits a loud 85 decibel alarm to be easily heard in case of an emergency. Alarm incorporates a self-diagnostic feature which will perform a self-check when the alarm powers on to ensure proper working order.

SINCE A SMOKE ALARM WILL NOT WORK WITHOUT POWER, having an alarm(s) that works from two completely different power sources, such as an AC direct wire with battery backup smoke alarm, can give you an extra measure of protection in case of an AC power failure or a dead battery. Battery operated alarms cannot work if the batteries are missing, disconnected or dead, if the wrong type of batteries are used or if the batteries are not installed correctly.

Shop our selection of Universal Security Instruments, Fire Safety in the Electrical Department at The Home Depot.

AC (only) powered alarms cannot work if the AC power is cut off for any reason. If you are concerned about the limitations of the battery or AC power, install both types of alarms. CO/NATURAL GAS alarms are designed to detect carbon monoxide and natural gases from any source of combustion or natural gas leakage that reaches their sensor. USING AN IONIZATION SMOKE ALARM IN A SMOKY AREA, SUCH AS A KITCHEN, OR IN A HIGH HUMIDITY AREA NEAR A SHOWER, CAN CAUSE NUISANCE FALSE ALARMS. IT IS PREFERABLE TO USE PHOTOELECTRIC ALARMS IN THESE AREAS. DO NOT TURN OFF THE AC POWER TO QUIET THE ALARM. A SMOKE ALARM WILL NOT HELP PROTECT YOU IF IT IS NOT POWERED. Properly locate your alarm to avoid nuisance alarms. A SMOKE ALARM MAY NOT ALWAYS WARN YOU ABOUT FIRES CAUSED BY CARELESSNESS AND SAFETY HAZARDS LIKE SMOKING IN BED, VIOLENT EXPLOSIONS, ESCAPING GAS, IMPROPER STORAGE OF FLAMMABLE MATERIALS, OVERLOADED ELECTRICAL CIRCUITS, CHILDREN PLAYING WITH MATCHES, NATURAL CAUSES SUCH AS LIGHTNING, OR ARSON. FIRE PREVENTION IS YOUR BEST SAFEGUARD. INSTALLING SMOKE ALARMS MAY MAKE YOU ELIGIBLE FOR LOWER INSURANCE RATES, BUT SMOKE ALARMS ARE NOT A SUBSTITUTE FOR INSURANCE.

Homeowners and renters alike should continue to insure their lives and properties. SMOKE ALARMS CANNOT DETECT FIRES IF THE SMOKE DOES NOT REACH THEM. Smoke from fires may not reach the sensing chamber and set off the alarm. One alarm should be installed inside each bedroom or sleeping area. Do not obstruct airflow around the smoke alarm or place in areas of obstructed airflow. BE AWARE OF VARIOUS SITUATIONS AGAINST WHICH THE SMOKE ALARM MAY NOT BE EFFECTIVE. For example: (1) Fires where the victim is intimate with a flaming initiated fire; for example, when a person's clothes catch fire while cooking; (2) Fires where the smoke is prevented from reaching the alarm due to a closed door or other obstruction or (3) Incendiary fires where the fire grows so rapidly that an occupant's egress is blocked even with properly located alarms.SMOKE ALARMS MAY NOT DETECT FIRE ON ANOTHER FLOOR OR AREA OF THE HOME. Recommended minimum protection is at least one smoke alarm in every sleeping area and every bedroom on every level of your home.

Interconnected smoke alarms may provide earlier warning than stand-alonesmoke alarms since all smoke alarms alarm when one detects smoke. SMOKEALARMS MAY NOT BE HEARD. WHAT YOU SHOULD KNOW ABOUT COCarbon monoxide (CO) is an insidious poison. It is a colorless, odorless, tasteless gas. It is a cumulative poison. Locate the first combination alarm in the immediate area of the bedrooms. Try to protect the escape route as the bedrooms are usually farthest from an exit. If more than one sleeping area exists, locate additional combination alarms in each sleeping area.

If a hall is more than 40 feet (12 meters) long, install a combination alarm at each end. Locate additional smoke alarms to protect any stairway as stairways act like chimneys for smoke and heat. Locate at least one combination smoke alarm on every floor level. Locate a smoke alarm in any area where a smoker sleeps or where electrical appliances are operated in sleeping areas.

Smoke, heat and other combustion products rise to the ceiling and spread horizontally. Mounting the smoke alarm on the ceiling in the center of the room places it closest to all points in the room. Ceiling mounting is preferred in ordinary residential construction. In general, install combination Smoke, CO and Gas Alarms:. WHERE YOU CAN HEAR THE ALARM FROM ALL SLEEPING AREAS.

In or near bedrooms and living areas or wherever you suspect a smoke, gas or CO exposure is likely. On each level of a multilevel home.IMPORTANT!Installation in an improper location can affect the sensitive electronic components in this alarm. Please review WHERE THIS ALARM SHOULD NOT BE INSTALLED (see Page 6).Not suitable for installation in hazardous locations as defined in the National Electric Code. This alarm will detect natural gas primarily and carbon monoxide secondarily. Natural gas events will always take precedence over carbon monoxide events. The word 'gas' will be used to specifically refer to natural gas.When on AC power, this alarm is designed to act as a continuous monitor.

It is not designed for use as a short-termtesting device to perform a quick check for the presence of CO or gas.BASIC SAFETY INFORMATION. This combination Smoke, Carbon Monoxide and Natural Gas alarm has separate alarms. This alarm is not designed to detect any other gas. Carbon monoxide and natural gas may be present in other areas.

The Smoke, CO and Natural Gas Alarm will only indicate the presence of CO or natural gas which reaches the sensor. Do not paint the alarm. Paint may clog the openings to the sensing chambers and prevent the unit from operating properly.

Do not stand too close to the unit when the alarm is sounding. It is loud to wake you in an emergency. Exposure to the horn at close range may harm your hearing.Make sure the alarm is not receiving excessively noisy power. Examples of noisy power could be major appliances on the same circuit, power from a generator or solar power, light dimmer on the same circuit or mounted near fluorescent lighting. Excessively noisy power may cause damage to your alarm.Find the pair of self-adhesivelabels included with this Smoke,CO and Gas Alarm. On each label, write in the phone number of your emergency responder (such as 911) and a qualified appliance technician.

Place one label near the Smoke, CO and Gas Alarm and the other label in the 'fresh air' location you plan to go to if the alarm sounds.This alarm cannot be operated from power derived from a square wave, modified square wave or modified sine wave inverter. These types of inverters are sometimes used to supply power in off-gridinstallations, such as solar or wind derived power sources. These power sources may produce high peak voltages which will damage the alarm.This unit should receive continuous electrical power. (The battery is meant for emergency backup only.) Choose an outlet where it can't be accidentally unplugged or switched off by children.

Keep small children away from the unit. Teach them not to play with it or unplug it. Explain what the alarms mean.Do not install this alarm into an electrical circuit controlled by a dimmer or switch or ground fault circuit interrupter.When testing the alarm, have someone else check that the alarm can be heard easily from the sleeping areas. The unit should be located where it can wake you if it alarms at night. RECOMMENDED PLACEMENT:NOTE: For any location, make sure no door or other obstruction could prevent the smoke, carbon monoxide or gas from reaching the alarm.WHERE THIS ALARM SHOULD NOT BE INSTALLEDTo avoid causing damage to the unit, to provide optimum protection, and to prevent unnecessary alarms. Do NOT locate this alarm:.

In garages, kitchens, crawl spaces and unfinished attics. Avoid extremely dusty, dirty or greasy areas.

Installation in these areas could lead to nuisance alarms, may expose the sensor to substances which could damage or contaminate it, or the alarm may not be heard by people in other areas of the home, especially if they are sleeping. In the garage, vehicle exhaust can contain some carbon monoxide. These levels are higher when the engine is first started. Within hours of starting a vehicle and backing it out of the garage, the levels present over time can activate the alarm and become a nuisance.

In the kitchen, some gas appliances can emit a short burst of CO or gas upon startup. This is normal. If your CO and Gas Alarm is installed too close to these appliances, it may alarm often and become a nuisance. Keep alarms at least 20 feet (6m) from the sources or combustion particles (stove, furnace, water heater, space heater), if possible.

In areas where a 20 foot (6m) distance is not possible (in modular, mobile or smaller homes for example), it is recommended the alarm be placed as far from these fuel-burningsources as possible. The placement recommendations are intended to keep these alarms at a reasonable distance from a fuel-burningsource and reduce 'unwanted' alarms. Unwanted alarms can occur if an alarm is placed directly next to a fuel-burningsource. Ventilate these areas as much as possible. Download mind map software.

If you must install the alarm near a cooking or heating appliance, install at least 5 feet (1.5m) from appliance. Curtains or heavy furniture may prevent CO or gas from reaching the sensor. Less than 12 inches (306mm) away from fluorescent lights. Electrical noise can interfere with the sensor. In extremely humid areas. This alarm should be at least 10 feet (3m) from a bath or shower, sauna, humidifier, vaporizer, dishwasher, laundry room, utility room or other source of high humidity. In very cold or very hot environments or in unheated buildings or outdoor rooms where the temperature can go below or above the operating range of the alarm.

Temperature limits for proper operation are 40 o to 100 oF (4.4 o to 37.8 oC). In turbulent air, such as near ceiling fans, heat vents, air conditioners, fresh air returns or open windows. Blowing air may prevent CO from reaching the sensors. Good ventilation is recommended when household cleaning supplies or similar contaminants are used. Excessive spillage or reverse venting of fuel-burningappliances caused by outdoor ambient conditions, such as: Wind direction and/or velocity, including high gusts of wind. Heavy air in the vent pipes (cold/ humid air with extended periods between cycles). Negative pressure differential resulting from the use of exhaust fans. Simultaneous operation of several fuel-burningappliances competing for limited internal air. Vent pipe connections vibrating loose from clothes dryers, furnaces or water heaters. Obstructions in or unconventional vent pipe designs which can amplify the above situations.THIS ALARM WILL NOT WORK WITHOUT 120 VAC POWER AND A GOOD BATTERY PROPERLY INSTALLED. THE ALARM SHOULD BE TESTED WHEN INSTALLED AND THEN TESTED WEEKLY AFTER THAT.INSTALLATION INSTRUCTIONS: CAUTION!!

READ CAREFULLY.Installation of this alarm must conform to the electrical codes in your area; Article 760 of the National Electrical Code, NFPA 72, 101; SBC (SBCCI); UBC (ICBO); NBC (BOCA): OTFDC (CABO), and any other local or building codes that may apply. Wiring and installation must be performed by a licensed electrician. Failure to follow these guidelines may result in injury or property damage.This alarm must be powered by a 24-hour,120V AC 60Hz circuit. Be sure the circuit cannot be turned off by a switch, dimmer or ground fault circuit interrupter. Failure to connect this alarm to a 24-hourcircuit may prevent it from providing constant protection.IMPORTANT: Do not subject this alarm to megger, high voltage or high-pottests. Remove the alarm(s) before high-pottingtests occur on the circuit or system. Section 55017, National Electric Code, 2002 Edition).ELECTRICAL SHOCK HAZARDTurn off power to the area where you will install this alarm at the circuit breaker or fuse box before beginning installation.

Failure to turn off the power before installation may result in serious electrical shock, injury or death.CAUTION: THIS SMOKE ALARM IS SEALED. THE COVER IS NOT REMOVABLE!. A mounting bracket is provided on the back of the alarm. Remove the mounting bracket from the back of the alarm by holding the mounting bracket and twisting the alarm in the direction indicated by the 'TWIST TO REMOVE' arrow on the side of the alarm base.OPTIONAL TAMPER RESISTANT FEATURES: There are two separate tamper resistant locking features provided for this model. Activating one or both of these features deters someone from removing the smoke alarm from the mounting bracket or removing the battery from the alarm. The breakaway locking pins are clearly marked and molded into the mounting bracket. Refer to the diagram on the next page.TO ACTIVATE THE LOCKING FEATURES: Do not activate the locking features until you have activated the battery, mounted the smoke alarm to the bracket and tested the smoke alarm.

Refer to OPERATION, TESTING & MAINTENANCE instructions.1. Detach the breakaway alarm locking pin from the mounting bracket.ALARM/BRACKETLOCKING PINBATTERY LOCKING PIN. Insert the pin into the hole for the feature you are activating. Refer to the diagram below for correct placement.INSERT ALARMINSERT BATTERYLOCKING PIN HERELOCKING PIN HERETO DEACTIVATE THE LOCKING FEATURES: To remove the alarm for cleaning or servicing or to replace the battery, you must first remove the appropriate locking pin, if it has been installed.1.

Turn off AC power to the circuit.2. Use long nose pliers to pull the locking pin out of the hole.3. It is now possible to remove the alarm or replace the battery.WIRING INSTRUCTIONS:1. The appropriate power supply is 120 Volt single phase power supplied from a non-switchablecircuit NOT protected by a ground fault circuit interrupter.b. Turn off AC power to the circuit before wiring the alarm.c. There are three pigtail wires (black, white and yellow) coming from the AC QUICK CONNECTOR. The proper wire connection is as follows:WIRES FROM QUICK CONNECTORCONNECT TOBLACK'HOT' side of AC lineWHITE'NEUTRAL' side of AC lineYELLOWInterconnect wires of other alarmsDO NOT TAMPER WITH WIRES WHEN POWER IS ON!For alarms that are used as single non-interconnected, stand-alonealarms, do not connect the yellow wire to anything.

Insulate this wire (tape it) in place to make certain the yellow wire cannot contact any metal parts.IInterconnected alarms can provide earlier warning of fire than stand-alonealarms, especially if a fire starts in a remote area of the dwelling. When alarms are interconnected, all alarms will sound when one alarm first goes into alarm.

This alarm may be interconnected with a total of not more than 24 interconnected devices, i.e., as many as 11 other USI ELECTRIC or UNIVERSAL model smoke alarms or combination smoke and carbon monoxide (CO and Natural Gas) alarms; 6 other initiating alarms which may be a combination of USI ELECTRIC or UNIVERSAL CO Alarms and Heat Alarms; and six other non-initiatingdevices such as USI ELECTRIC Relay Modules. Compatible models include: 2995, 5304, MI100, MI106, MDS101, MDS107, MDS211, 2985, 5303, MI200, MI210 USI-1103, USI-1203, USI-1204, USI-1208(Part #USI-1209), USI-1213, USI-3204, USI-7385, USI-7390, USI-7485, USI-7490, USI-7795, USI-2430, USI-960, SS-785, SS-790, SS-795, SS-2795, SS-2895, CD-9385, CD-9390, CD-9485, CD-9490, CD-9795, HD-130, RM-100.Interconnected CO alarms or CO alarm circuit of combination smoke and CO and Natural Gas alarms will only respond if a CO alarm / event initiates the alarm. All other alarms remain silent.Interconnected combination Natural Gas Alarms will only respond if a natural gas event initiated the alarm. All other alarms remain silent.Interconnected smoke alarms, heat alarms and relay modules will only respond if a smoke alarm / event or heat alarm / event initiates the alarm. All CO and Natural Gas alarms remain silent.Note that smoke alarms without battery backup will not respond during an AC power failure.

NOTE: Relay Modules/USI-960will not respond if a CO alarm / event initiates the alarm.Page 8. The yellow wire is used only for multiple station operations with USI ELECTRIC or UNIVERSAL Model alarms only. Connecting this yellow wire to any other circuits may result in damage and alarm malfunction. When alarms are interconnected, all alarms must be powered from a single AC branch circuit.

If local codes do not permit, be sure the neutral wire is common to both phases. The maximum wire run distance between the first and last alarm/device in an interconnected system is 1,000 feet. NOTE: Use standard household wire (18 gauge or larger, rated at least 300V, as required by local codes) available at all electrical supply/hardware stores.The wiring to be used shall be in accordance with the provisions of Articles 210 and 300.3(B) of the National Electrical Code, ANSI/NFPA70. In addition, the resistance of the interconnecting wiring shall be a maximum of 10 Ohms.2.

Attach the mounting bracket to the electrical junction box.3. To activate 9 volt battery and alarm, hold the QUICK DRAW (R) battery drawer closed, pull and remove the PULL-TAB.Confirm that the entire PULL-TABhas been completely removed. Discard PULL-TAB.4. Plug the AC QUICK CONNECTOR into the alarm base. Push and twist the alarm clockwise onto the mounting bracket.5.

Usi Electric Smoke And Carbon Monoxide Detector Manual

See 'OPTIONAL TAMPER RESISTANT FEATURES' and 'TO ACTIVATE THE LOCKING FEATURES' instructions on Page 7.6. Turn on AC power and check the LED's for proper operation. The green LED should be on to indicate AC power. The red LED blinks on once approx. Every 40 seconds to indicate proper operation.IMPORTANT!The battery backup is designed to provide short-termemergency power to the CO and Gas Alarm. Actual backup time depends on the strength (freshness) of the battery. The battery backup will not work unless a good battery is properly installed.When the alarm utilizes battery backup power, the natural gas sensor will operate the alarm and will sample less frequently to extend battery life.

Natural gas could be present during this period between samples without the alarm sounding, especially if there is a rapid buildup of natural gas.OPERATION, TESTING & MAINTENANCEOPERATION: The alarm is operating once the AC power is connected and turned on (the battery must also be installed). When products of combustion are sensed, the alarm sounds a loud alarm which continues until the air is cleared.LOW BATTERY ALARM: If the alarm chirps once approx. Every 40 seconds, please verify that the battery activation pull tab has been completely removed, the battery polarity is correct and the battery terminals are making contact with the alarm contacts in the battery compartment. If the battery continues to chirp, replace the 9 volt battery.This alarm incorporates the NFPA recognized horn signal for evacuation. During alarm mode, the horn produces three beeps followed by a two second pause and then continually repeats.READY/ACTIVE CONDITION: The red LED blinks on once approx. Every 40-45seconds to indicate the alarm is properly functioning.LOCAL ORIGINATING SMOKE ALARM CONDITION: The red LED blinks on approx. Every 2 seconds and the alarm emits a loud, pulsating alarm sound.NON-ORIGINATING SMOKEALARM CONDITION: The red LED is off and the alarm emits a loud, pulsating alarm.GREEN LED: The green LED is on whenever AC power is turned on.CO ALARM: The alarm signal is 4 beeps, 2 second pause, repeat.

The green LED turns off when the 4 beeps start. The red LED blinks in sync with the cycle of 4 beeps.GAS ALARM: The alarm signal is 1 beep, 1 second pause, repeat. The green LED blinks off. The blue LED blinks in sync with the horn beep every second.NUISANCE ALARM: If the horn signals for no apparent reason and no obvious hazard is present, please verify that the alarm is mounted in the correct location. Reset the alarm as instructed in the Operational Summary. SMOKE ALARM LATCHING LED INDICATOR: The alarm had prevously detected smoke and had alarmed. The red LED is off and blinks on every 5 seconds until reset.

Follow the reset instructions to remove the latching LED.CO ALARM LATCHING LED INDICATOR: The alarm had previously detected CO and had alarmed. The red LED is off and blinks on every 5 seconds until reset.

Follow the reset instructions to remove the latching LED.GAS ALARM LATCHING LED INDICATOR: The alarm had previously detected GAS and had alarmed. The blue LED is off and blinks on every 5 seconds until reset. Follow the reset instructions to remove the latching LED (see below).TROUBLE / SERVICE ALARM: Periodically, the alarm measurement circuit is tested.

If an error is detected, the alarm will sound 3 chirps approx. Every 20 seconds. Replace the alarm.END-OF-SERVICE LIFE ALARM: When it is time to replace your alarm, which is approximately 7 years of operation from initial power up, the alarm will sound 2 chirps approx. Every 20 seconds.

The allarm should be replaced immediately.RESET THE ALARM: Press the TEST/SILENCE button for 10 seconds and then release. This will clear the alarm LED's and clear the SILENCE mode.TESTING: Test by pushing the Test button on the smoke alarm cover until the alarm sounds, then release. The alarm sounds if all electronic circuitry, horn and battery are working. If no alarm sounds, the alarm may have a power supply failure.

Home depot

Test the smoke alarm weekly to assure proper operation.ALARM ORIGINATION: The QUICK FIND ® Alarm Origination Feature allows the user to identify the initiating alarm smoke alarms in an interconnected alarm system. If an interconnected alarm system is initiated by one of the alarms, when the alarm system exits alarm condition, the user can identify the initiating alarm by:a. Pressing and releasing the test button on any alarm in the system.b. Interconnected alarms will sound and then stop.c. The originating smoke alarm will continue to sound 60 seconds to allow ample time to quickly find originating alarm.IF YOUR CO AND GAS ALARM SOUNDSWHAT TO DO IF CARBON MONOXIDE IS DETECTED:If you hear the alarm horn sound 4 beeps, a 5 second pause (and then repeat), carbon monoxide has been detected. Evacuate everyone from the building.Actuation of your CO Alarm indicates the presence of carbon monoxide (CO), which can kill you.

In other words, when your CO Alarm sounds, you must not ignore it!Some individuals are more sensitive to CO than others, including people with cardiac or respiratory problems, infants, unborn babies, pregnant mothers or elderly people can be more quickly and severely affected by CO. Members of sensitive populations should consult their doctors for advice on taking additional precautions.IF THE CO ALARM SOUNDS:1. Operate SILENCE button;2. Call your emergency services, fire department or 911.

Write down the number of your local emergency service here:3. Immediately move to fresh air - outdoors or by an open door/window. Do a head count to check that all persons are accounted for.

Do not reenter the premises nor move away from the open door/window until the emergency services responders have arrived, the premises have been aired out and your alarm remains in its normal condition.4. After following steps 1-3,if your alarm reactivates within a 24 hour period, repeat steps 1-3and call a qualified appliance technician to investigate for sources of CO from fuel-burningequipment and appliances and inspect for proper operation of this equipment. If problems are identified during this inspection, have the equipment serviced immediately. Note any combustion equipment not inspected by the technician and consult the manufacturers' instructions or contact the manufacturer(s) directly for more information about CO safety and this equipment. Make sure that motor vehicles are not, and have not been, operating in an attached garage or adjacent to the residence. Write down the number of your local emergency service here.

WHAT TO DO IF NATURAL GAS IS DETECTED:If you hear the alarm horn sound 1 beep per second, gas has been detected. Evacuate everyone from the building.1. Leave the house immediately, opening doors and windows as you leave.2.

Do not use your telephone or appliances. Do not turn any light switches off or on. Any spark or flame could ignite the gas.3. Call 911 and your gas company from a phone that is away from your home.4. Do not reenter the area until the source of the leak is found and corrected.If the unit alarms and you are not testing the unit, it is warning you of a potentially dangerous situation which requires your immediate attention.

NEVER ignore any alarm. Ignoring the alarm may result in injury or death.USING THE SILENCE FEATURENEVER disconnect the power to your alarm to silence the horn - use the Silence feature. Disconnecting the alarm removes your protection!.

The Silence feature is intended to temporarily silence the horn while you identify and correct the problem. To use the Silence feature, press and release the TEST/SILENCE button until the horn is silent if it was the i nitiating alarm.

If the TEST/SILENCE button is pressed while the alarm is in the silence mode, the alarm will start sounding again.WHEN THE CO ALARM SIGNAL IS SILENCED: The CO alarm will remain silent for up to 4 minutes (with the red LED blinking on approx. Every 10 seconds, until reset) and then return to normal operation. It will continue to monitor the air for CO.

Ventilate area. After up to 4 minutes, depending on the level of CO detected, if CO levels remain potentially dangerous, the horn will start sounding again.WHEN THE GAS ALARM SIGNAL IS SILENCED: The alarm will remain silent for approximately 20 seconds (with the blue LED blinking on approx. Every 10 seconds, until reset) and then return to normal operation. Ventilate area. If the gas has not cleared within the silence period, the unit will go back into alarm.WHEN THE SMOKE ALARM SIGNAL IS SILENCED: The alarm will remain silent for up to 8-12minutes (witht he red LED blinking on approx.

Every 5 seconds until reset) and then return to normal operation. Ventilate area. If the smoke has not cleared within the silence period, the unit will go back into alarm.IMPORTANT!The Silence feature is intended to temporarily silence the alarm horn. It will not correct a Smoke, CO or Natural Gas problem.RESET: To reset the QUICK FIND ® Alarm Origination condition, press and hold the TEST/SILENCE button on any alarm for at least 10 seconds and then release. Reset after each alarm.

The reset feature will reset all interconnected units.TROUBLE/SERVICE ALARM: If the alarm beeps 3 times approx. Every 40 seconds after the red LED flashes and cannot be restored to normal operation, the alarm should be replaced.immediately.END-OF-SERVICE LIFE NOTIFICATION: A majority of home fire deaths are a result of no smoke alarms or no working smoke alarms. In addition to the 'replace by date' stamped on the back of your alarm, your alarm contains a unique audible end-of-servicelife notification feature. When it is time to replace your alarm, which is after approximately 10 years of operation from initial power up, the alarm will sound 1 beep approx. Every 60 seconds and the red LED will blink on once approx. Every 40-45seconds.

The green LED stays on. The alarm should be replaced immediately.The end-of-servicelife signal can be silenced for approximately 6 hours. To perform this function, press and release the test button.

The alarm will sound for approximately 60 seconds while it resets. After the reset function is completed, the alarm will be silent for approximately 6 hours. The end-of-service life signal will activate after the silence period. NEVER use an open flame of any kind to test this smoke alarm. You might accidentally damage or set fire to the smoke alarm or to your home. The built-intest switch accurately tests the smoke alarm's operation as required by Underwriters Laboratories Inc. (UL).(UTHA) Sensitivity Indicating MeansThe sensitivity indicating means for this Smoke and Fire Alarm is the use of the analyzer for Smoke Detectors Model 501-Aor 501-A/BatAerosol Generator Manufactured by Gemini Scientific Corp., 1122-BAster Ave., Sunnyvale, CA 94086.The Equivalent UL 268 Light obscuration%/Ft as measured by this instrument must be within the obscuration listed on the back of this alarm.(UTHA) Go/No-GoField TestThe Go/No-Gotest for this smoke and fire alarm is to use one of the following UL listed can-typeaerosol smoke alarm testers.

The instructions for use are printed on the canister. Home Safeguard, Model 25S.If you choose to use an aerosol smoke product to test the smoke alarm, be certain to use one that has been Listed to Underwriters Laboratories, Inc. Safety Standards and use it only as directed. Use of non-ULListed products or improper use of UL Listed products may affect the smoke alarm's sensitivity.(UTHA) MAINTENANCE:The alarm is virtually maintenance free. However, under dusty conditions, a vacuum hose may be used to clear the sensing chamber of dust.Clean the alarm at least once a month to remove dust, dirt, insects or debris.

Always turn off power to alarm before cleaning. Using a soft brush or wand attachment to a vacuum cleaner, vacuum all sides and cover of thr alarm. Be sure all the vents are free of debris.If the alarm is false alarming and cannot be restored to normal operation, the alarm should be replaced.WEEKLY TESTING. NEVER use an open flame of any kind to test this unit. You might accidentally damage or set fire to the alarm or to your home. The built-intest switch accurately tests the unit's operation as required by CSA 6.19-01Standard. NEVER use vehicle exhaust!

Exhaust may cause permanent damage and voids your warranty. DO NOT stand close to the alarm when the horn is sounding. Exposure at close range may be harmful to your hearing. When testing, step away when the horn starts sounding.It is important to test this alarm every week to make sure it is working properly.USING THE TEST FEATURE:Press and release the TEST button on the alarm cover.During testing, you will hear: 3 beeps (red LED on), 2 second pause, 5 beeps (blue LED on), 2 second pause, 4 beeps (red LED on).If the alarm does not sound properly:1.

Make sure the AC power is applied and the battery is fresh and installed correctly.2. Test the alarm again.REGULAR MAINTENANCECLEANING YOUR ALARM:DO NOT use spray cleaning chemicals or insect sprays directly on or near the alarm. DO NOT paint over the alarm. Doing so may permanently damage the alarm.The outside can be wiped with a damp cloth. Do not use any household cleaning agents, ammoniabased cleaners, paints, varnishes or any other chemical on or near your alarm.

AFTER CLEANING,REINSTALL YOUR ALARM. TEST YOUR ALARM BY USING THE TEST BUTTON.Page 12. BACKUP BATTERY REPLACEMENTDisconnect AC power before changing battery.

Shock hazard exists if AC power is miswired.The alarm uses a 9 Volt battery. The battery should last for at least one year under normal operating conditions. The alarm has a low battery indicator, an audible beep or chirp. It will operate at approx.

40 second intervals for a minimum of 7 days. When this indication occurs, replace the battery with an Alkaline type (Energizer #522, Duracell #MN1604), or Lithium type (Ultralife U9VL-J)from your local retailer.LITHIUM Battery Models only - The LITHUM battery is warranted to last for 10 years under normal operating conditions. Replace the battery with only LITHIUM type: (ULTRALIFE: U9VL-J.OPTIONAL BATTERY DRAWER TAMPER LOCKING PIN: To make your battery drawer tamper resistant, a locking pin has been provided (breakaway part on mounting bracket).NOTE: If this feature has been activated, you will need to deactivate it by removing the battery drawer tamper pin located at side of battery drawer.

Refer to Page 5.Pull the QUICK DRAW (R) battery drawer open and remove the battery. While observing polarity, push the replacement battery into the battery drawer until it is held securely in place.

Carefully close the battery drawer and reinstall the tamper pin.Test the smoke alarm by pushing the TEST button on the smoke alarm cover until the alarm sounds, then release.OPTIONAL BATTERY DRAWER TAMPER LOCKING PIN: To make your battery drawer tamper resistant, a locking pin has been provided (breakaway part on mounting bracket).NOTE: If this feature has been activated, you will need to deactivate it by removing the battery drawer tamper pin located at side of battery drawer.Pull the QUICK DRAW (R) battery drawer open and remove the battery. While observing polarity, push the replacement battery into the battery drawer until it is held securely in place. Carefully close the battery drawer and reinstall the tamper pin.Test the smoke alarm by pushing the TEST/SILENCE button on the alarm cover until the alarm sounds, then release.CO AND NATURAL GAS ALARM LIMITATIONSAlarms have limitations. Like any other electronic device, Smoke, CO and Natural Gas alarms are not foolproof.Smoke, CO and Natural Gas alarms have a limited operational life. Your alarm must be tested weekly, because it could fail to operate at any time. If your aAlarm fails to test properly, or if its selfdiagnostic test reveals a malfunction, immediately have the unit replaced (see last page for warranty information).Smoke, CO and Natural Gas alarms can only sense CO which reaches the alarm's sensor. Carbon monoxide may be present in other areas without reaching the alarm.CO or gas could be present on one level of the home and not reach the alarm installed on a different level.

For example, CO or gas in the basement may not reach an alarm on the second level, near the bedrooms. For this reason, we recommend you provide complete coverage by placing a Smoke, CO and Natural Gas alarm on every level of the home.Smoke, CO and Natural Gas alarms are not a substitute for property, disability, life or other insurance of any kind. The following conditions can result in transient CO situations:1.

Excessive spillage or reverse venting of fuel-burningappliances caused by outdoor ambient conditions, such as:. Wind direction and/or velocity, including high gusts of wind. Heavy air in the vent pipes (cold/ humid air with extended periods between cycles). Negative pressure differential resulting from the use of exhaust fans.

Simultaneous operation of several fuel-burningappliances competing for limited internal air. Vent pipe connections vibrating loose from clothes dryers, furnaces or water heaters.

Obstructions in or unconventional vent pipe designs which can amplify the above situations.2. Extended operation of unvented fuel-burningdevices (ranges, ovens, fireplaces).3.

Temperature inversions which can trap exhaust close to the ground.4. A car idling in an open or closed attached garage or near a home.HOW CAN I PROTECT MY FAMILY FROM CO POISONING?This alarm is an excellent means of protection. It monitors the air and sounds a loud alarm before carbon monoxide levels become threatening to the average, healthy adult.An alarm is not a substitute for proper maintenance of home appliances.To help prevent CO problems and reduce the risk of CO poisoning:. Clean chimneys and flues yearly. Keep them free of debris, leaves and nests for proper air flow. Also, have a professional check for rust and corrosion, cracks or separations. These conditions can prevent proper air movement and cause backdrafting.

Never 'cap' or cover a chimney in any way that would block air flow. Test and maintain all fuel-burningequipment annually. Many local gas or oil companies and HVAC companies offer appliance inspections for a nominal fee. Make regular visual inspections of all fuel-burningappliances. Check appliances for excessive rust and scaling.

Also check the flame on the burner and pilot lights. The flame should be blue. A yellow flame means fuel is not being burned completely and CO may be present. Keep the blower door on the furnace closed.

Use vents or fans when they are available on all fuel-burningappliances. Make sure appliances are vented to the outside. Do not grill or barbecue indoors or in garages or screen porches. Check for exhaust backflow from CO sources. Check the draft hood on an operating furnace for a backdraft. Look for cracks on furnace heat exchangers.

Check the house or garage on the other side of a shared wall. Keep windows and doors open slightly.

If you suspect that CO is escaping into your home, open a window or a door. Opening windows and doors can significantly decrease CO levels.REPAIRS AND SERVICESIf the smoke alarm is defective in any way, do not tamper with the smoke alarm. Return the alarm for servicing. (See warranty for instructions or in-warrantyreturns.) There will be a service charge for repairing out of warranty alarms.DEVELOP AND PRACTICE A PLAN OF ESCAPE BASICS OF ESCAPE PLANo Make a floor plan indicating all doors and windows and at least two escape routes from each room.

Second story windows may need a rope or chain ladder.o Have a family meeting and discuss your escape plan, showing everyone what to do in case of fire. O Determine a place outside your home where all of you can meet if a fire occurs.o Familiarize everyone with the sound of the smoke alarm and train them to leave your home when they hear the sound.o Identify children's bedrooms with red stickers placed in the upper left corner of the windows. They are available from your local fire department.o Practice a fire drill at least every six months. Practice allows you to test your plan before an emergency. You may not be able to reach your children.

It is important they know what to do! WHAT TO DO WHEN THE ALARM SOUNDSo Leave immediately by your plan of escape. Every second counts, so don't waste time getting dressed or picking up valuables.o In leaving, don't open any inside door without first feeling its surface. If hot, or if you see smoke seeping through cracks, don't open that door! Instead, use your alternate exit. If inside door is cool, place your shoulder against it, open it slightly and be ready to slam it shut if heat and smokerush in.o Stay close to the floor if air is smoky.

Breathe shallowly through a cloth, wet if possible. O Once outside, go to your selected meeting place and make sure everyone is there.o Call the fire department from your neighbor's home – not from yours! O Don't return to your home until fire officials say that it is all right to do so.REPAIRS AND SERVICESIf the smoke alarm is defective in any way, do not tamper with the smoke alarm. Return the smoke alarm for servicing. OPERATIONAL SUMMARYCONDITION OF ALARM AUDIBLE & VISUAL SIGNALS BEFORE SOLUTION / RECOMMENDATIONPOWERGASCOSOLUTION /HORNGREEN LEDBLUE LEDRED LEDRECOMMENDATIONSilentOn and BlinksOffOffAC Power is present. DC power is presentoff approx every20 secondsSilentOff and BlinksOffOffAlarm is powered by battery backup. AC Power is noton approx everypresent.

Check the breaker or fuse box for power. If the40 secondsbreaker or fuse box looks normal, call a licensedelectrician for assistance.1 beep,Turns offBlinks inBlinks inThe TEST button has been pressed.

TEN YEAR LIMITED WARRANTYMODELS MICN102, MICN102LMODELS MICN109, MICN109LUSI ELECTRIC, INC./UNIVERSAL SECURITY INSTRUMENTS, INC. ('USI') warrants your USI product to be free from defects in material and workmanship for a period of ten (10) years from the date of purchase. This warranty shall not apply to any batteries used in the product or to any damage which may be caused by such batteries.This warranty applies only to the original consumer purchaser and only to products used in normal residential use and service.

If this product is found to be defective, USI's only obligation, and your exclusive remedy, is the repair or replacement of the product, at USI's discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alteration, neglect or mishandling. This Warranty shall not apply to any product which is found to have been improperly installed, set-up,or used in any way not in accordance with the instructions supplied with the product.TEN YEAR LITHIUM BATTERY LIMITED WARRANTY.This battery is warranted by Ultralife Batteries, Inc. For a 10 year life. ONLY in this CO/Gas Alarm and is not warranted in any other device. Improper handling and/or installation of the battery voids the warranty.

Improper handling and/or installation includes, but is not limited to:A. Reversing the battery's polarity or connecting the battery's '+' and '-'terminals incorrectly.B. Short circuiting the battery.C. Attempting to charge the battery.D.

Subjecting the battery to excessive humidity, hot or cold conditions.E. Altering the battery physically in any way.ULTRALIFE 9 VOLT BATTERY RETURNS:To return the Ultralife Battery under warranty, send battery ONLY along with a note describing nature of difficulty and proof of date of purchase, postage prepaid and return postage to:ULTRALIFE BATTERIES, INC.C/O UNIVERSAL SECURITY INSTRUMENTS, INC. BOX 6221350 ROUTE 88 SOUTH NEWARK, NEW YORK 14513 USAALARM RETURNS:For replacement of this alarm under the terms of this Warranty, contact our Customer Service line at 1-800-390-4321,Ext. 238, for current postage and handling fees.USI DOES NOT WARRANT AND SPECIFICALLY DISCLAIMS ANY WARRANTY, WHETHER EXPRESS OR IMPLIED, OF FITNESS FOR A PARTICULAR PURPOSE, OTHER THAN THE WARRANTY CONTAINED HEREIN. NO IMPLIED WARRANTY ON THIS PRODUCT, CREATED BY STATE LAW, SHALL EXTEND BEYOND THE TERM OF THIS WARRANTY UNLESS SUCH LAW OTHERWISE PROVIDES.